May 26, 2009 @ 2:25 pm
Is it wise to hang drywall over paneling that has plaster walls behind the panels?
Our house was built back in the 1940’s and originally had plaster walls throughout. Sometime between then and now, somebody hung faux wood paneling over all of the plaster walls. We’re not big fans of this look and would like to hang drywall.
We thought we could just hang the drywall over top of the paneling, but someone mentioned to me that if the plaster behind the paneling gave way, the drywall would fall in.
Should we go ahead with the original plan, or do we need to tear our current walls down to the studs before we hang the drywall?
Removing the paneling as suggested will cause more damage to the lath and plaster under it. This is due to the fact that most paneling is hung using paneling nails as well as glue. If gutting the room is not in your budget then by all means go with your initial plans. I have done this in several homes where finances were tight. In most cases things turned out nice. In a couple since the rooms were not square the ceiling and walls were a bit wavy where they met. A quick fix for that is crown molding or a decorative border.
Filed under How To Plaster Permalink
6 Comments »
RSS feed for comments on this post · TrackBack URI
Posted by Christina A
February 10, 2010 @ 8:11 pm
Can you not just remove the panelling and patch the plaster behind? if not I suggest removing it all and replacing with drywall. You have no idea whats going on behind the panels and it could get a whole lot more costly down the road. We had panelling in our basement and ripped it off and plastered the holes.
References :
home diy experience
Posted by Diane A
February 10, 2010 @ 8:21 pm
In this instance, it would probably be worthwhile to spend a little more upfront and do it right than cheap now & re-do later. I agree with the other poster–can you not remove the panels and patch the plaster? Plastered walls are a much better product than drywall in any case. But to just cover up what’s there with drywall could be very problematic–water damage, inappropriate tensile strength to the wall for hanging things, panels warping, termites. If you did this you would also have to disclose this when you sold as its a non standard construction. You would also have problems with casings and electrical connections as the walls will be thicker than standard.
References :
Interior designer
Posted by uclueletbc
February 10, 2010 @ 8:35 pm
I’d just hang it over everything your going to have to widen the door and window jams….I’d use a 1/2 drywall and not the 1/4 inch to get the stiffness…use screws to attach the board…hammering all nails could break the plaster….alot of waste material if u tear everything down
References :
Posted by quality r
February 10, 2010 @ 8:55 pm
The easiest and cheapest way is to cap or install new sheetrock over the top. Make sure to correct any wiring or plumbing issues before hand. This is a very common practice. You will have to add or install new trim on doors and windows.
Good luck and happy rocking
References :
remodel contractor
Posted by frenchcountryplus
February 10, 2010 @ 9:28 pm
Removing the paneling as suggested will cause more damage to the lath and plaster under it. This is due to the fact that most paneling is hung using paneling nails as well as glue. If gutting the room is not in your budget then by all means go with your initial plans. I have done this in several homes where finances were tight. In most cases things turned out nice. In a couple since the rooms were not square the ceiling and walls were a bit wavy where they met. A quick fix for that is crown molding or a decorative border.
References :
Professional interior decorator for 21 years.
Posted by dandyrandywhitetruck
February 10, 2010 @ 9:42 pm
just screw it right to the panel, anywhere you want. it is not necessary to locate studs. glue the back of the paneling and use wood screws.
References :
25 years commercial carpenter